iddaa tahminleri banko tahmin gaziantep escort ankara escort ankara escort izmir escort antalya escort izmir escort porno porno izle bursa escort escort porno havalandirma sistemleri izmir escort bursa escort izmir escort izmir escort istanbul escort
PCV intake fitting question
500 Madness
   
Results 1 to 5 of 5

Thread: PCV intake fitting question

  1. #1
    Junior Member
    Join Date
    Jun 2019
    Location
    Miami Beach, FL
    Posts
    23
    Thanks
    0
    Thanked 4 Times in 3 Posts

    PCV intake fitting question

    Hey, does anyone know if the quick connect going to the intake tube is 1/4, 5/16 or 3/8? I'm not near my car to measure, and trying to pre-order some stuff.

    Inked2012-fiat-500-abarth-engine-bayjpg_LI.jpg
    2013 500 Abarth:
    - MPx Axle Back Exhaust
    - PTP Lava Turbo Blanket

  2. #2
    Junior Member
    Join Date
    Oct 2018
    Location
    Arizona
    Posts
    27
    Thanks
    1
    Thanked 5 Times in 5 Posts
    I have a 2018 so I only have one vacuum line (the "lower" one on your set-up), its 6 mm

  3. #3
    Lifetime Member Lifetime Member Saponetta's Avatar
    Join Date
    Sep 2018
    Location
    St. Louis missouri
    Posts
    1,152
    Thanks
    34
    Thanked 284 Times in 224 Posts
    The quick is 10mm barb is 6. 3/8 and 1/4 I believe.
    2013 abarth
    Spec 2+ clutch
    Working on new divided turbo setup
    Homebrew fmic w/ corsa forza hoses
    Stock Downpipe with cat and 2.25discharge
    Coils
    Homemade cowl intake
    ECB yellows/stop tech fluid
    Koni/vogtland
    Braces and strut mounts
    Corsa forza vento
    E30 blend

    2013 abarth tork tuned
    cowl intake, custom fmic and bypass valve, vogtlands, rear vette bilstiens, long 3 inch downpipe to stock rear section.

  4. #4
    Junior Member
    Join Date
    Jun 2019
    Location
    Miami Beach, FL
    Posts
    23
    Thanks
    0
    Thanked 4 Times in 3 Posts
    Thanks guys. I'll just order a 5/16 and 3/8 (10mm.. ish) to be safe and reply again when I know which if anyone ever needs to know too.
    2013 500 Abarth:
    - MPx Axle Back Exhaust
    - PTP Lava Turbo Blanket

  5. #5
    Junior Member
    Join Date
    Jun 2019
    Location
    Miami Beach, FL
    Posts
    23
    Thanks
    0
    Thanked 4 Times in 3 Posts
    For the record: the size for the larger hose is 3/8"
    2013 500 Abarth:
    - MPx Axle Back Exhaust
    - PTP Lava Turbo Blanket

Similar Threads

  1. Question: Best air intake and why
    By dsetch in forum Fiat 500 ABARTH Engine and Drivetrain Tuning
    Replies: 34
    Last Post: 06-12-2018, 12:09 PM
  2. Odd Intake Question
    By Ando in forum Fiat 500 ABARTH Engine and Drivetrain Tuning
    Replies: 8
    Last Post: 04-20-2017, 12:06 AM
  3. Air Intake Question
    By Muugi in forum Fiat 500 ABARTH Engine and Drivetrain Tuning
    Replies: 5
    Last Post: 12-23-2014, 02:08 PM
  4. Another intake question
    By tknospdr in forum Fiat 500 ABARTH Engine and Drivetrain Tuning
    Replies: 15
    Last Post: 12-14-2013, 11:17 PM
  5. Road///Race Abarth Intake - Test Fitting & Analysis
    By redred in forum Fiat 500 ABARTH Engine and Drivetrain Tuning
    Replies: 47
    Last Post: 07-01-2013, 11:02 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •