bahis siteleri Betboo yeni adresi izmir escort antalya escort izmir escort porno porno izle bursa escort escort mobil porno havalandirma sistemleri takipçi satın alma instagram beğeni hilesi instagram takipçi hilesi saha betonu izmir escort eskişehir escort bayan Bought all new Turbo black headlights/signal/tails (Pic) and Mopar Part numbers - Page 2
500 Madness
Page 2 of 2 FirstFirst 1 2
Results 11 to 12 of 12

Thread: Bought all new Turbo black headlights/signal/tails (Pic) and Mopar Part numbers

  1. #11
    Junior Member gadaboutgolfer's Avatar
    Join Date
    Nov 2013
    Thanked 2 Times in 2 Posts

    Turbo tail lights on Abarth Cabrio

    Hi. I bought the Mopar Turbo black trim tail lamps and installed them today. Beware, they do not fit on Abarth Cabrio! Since the Cabrio has a trunk, the trunk hinge is allowed for on the Abarth tail light housing. But since I already had the beautiful new lights, and a little grit and determination, I used a very sharp knife and whittled/carved the plastic housing to allow room for the hinge on the new lights. Installed successfully, and they look great. Now I just need to decide if I should also do the headlights and turns up front. Advice? I still intend to keep the other chrome accents at this point.

    Attaching photos of the original and the new so you can see the modification I had to make. (Sorry I don't know how to get the photos in the right order from my iPad, but you'll figure it out)

    Attachment 14355image.jpgimage.jpgimage.jpgimage.jpgimage.jpg

  2. The Following User Says Thank You to gadaboutgolfer For This Useful Post:

    bomba (09-13-2014)

  3. #12
    Senior Member bomba's Avatar
    Join Date
    Mar 2014
    Thanked 59 Times in 40 Posts
    Thanks for posting. I figured that they wouldn't fit my Cabrio because Madness sells different tail lights for both models, so I held off. It looks like it shouldn't be too difficult with a dremel, but I'd be wondering if they will let condensation in and fog up like some OEM ones do.
    2013 Rosso Abarth Cabrio

    RRM V3 ECU, BMC CAI, Madness GoPedal, MPx Throttle Body, Forge Actuator, Craven Throttle Body Spacer, GFB DV+, ATM FMIC, RRM Lightweight Pulley, Craven Short Shift Kit, Neu-F Torque Arm Insert

    Madness Mild Drop Springs, Koni Yellow Rear Shocks, Front Strut Bar, Rear 25mm Torsion Bar, Craven Short Shift Kit, CPR Lower Brace Bar

    Madness Xenon Light Kit, Tributo Badges & Stripes, Madness Black Painted Tail Lights.

Page 2 of 2 FirstFirst 1 2

Similar Threads

  1. Black Trimmed Headlights!
    By MADNESSLuckyJay in forum Fiat 500 ABARTH Images
    Replies: 9
    Last Post: 03-10-2013, 11:45 PM
  2. My Bianco Abarth with 500T/Mopar Blacked-Out tails
    By Tom2.0 in forum Fiat 500 ABARTH Images
    Replies: 22
    Last Post: 01-07-2013, 12:20 AM
  3. TOM TOM Dash Dock Part numbers?
    By deathshead in forum Fiat 500 General Discussion
    Replies: 3
    Last Post: 11-28-2012, 11:47 PM
  4. Das Part Numbers
    By John Reid in forum Questions about the Fiat 500
    Replies: 1
    Last Post: 06-20-2012, 11:45 AM
  5. Fiat 500 Takes Part in Mopar's 75th Anniversary Celebration
    By Fiat500USA in forum Articles and Story Comments
    Replies: 4
    Last Post: 01-31-2012, 04:46 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts